Відео

I can’t see how much that is off but I proved that the top dot is slightly off from factory in one of my videos with lazer and my bike runs great. The timing in the book is explained differently on the dots with the top of the head and counting cam chain pin links.

What would cause one of these models to make a knocking sound?

Hey man, I have a question. If the factory size jet is 38, but you ended up with a 52, what happened? Is there some other issue that made it necessary to change the jet size? Did you also have to change out the main jet too? Ok I had 3 questions.

I’d say any old shindaiwa is worth fixing… “First to start last to quit” ended when echo ruined them. Found a NOS Shindaiwa T2500… I bought it on the spot. Maruyama is the only current trimmer I’d buy.

Hey! Liked and subscribed! Great video!

Nice work. I was not so lucky :)

Bendiciones,tengo uno,y no se , repararlo, as yuda , por favor, bendiciones

Whats that program for valve clearance?

Thank God for this video, our 79 kombi van was idling way too low and thanks to this video we found the screw to adjust the idle speed, cheers from Perth Australia 😊

where did you get the side tank grips and size

Not sure why some want to push the end into the small end of the boot. Good call

you do good job but no one shows where the timeing marks on the magneto go i have a kx250f need timeing done

What other motorcycle brand parts is the husky 650 compatible with?

Hey... I just wanted to thank-you. I have a 66 Honda S90 and your video helped me figure out the no spark issue. The comment section is not turned on in that video so I commented on this vid. Thanks again

Best way to assess top dead center is to take two points before and after tdc at the same distance (5mm / 1/4") and then to take the middle. Much more accurate...

This looks fun to drive

Wow

Exact same thing happened to me. But couldn't find the manufacturer. Do you have a contact?

Hello @gizmowerks can you help me find the full kit of husqvarna tr650s crankshaft...

Just out of curiosity, have you tried the TR 650 Terra? Its 21" spoked front wheel opens up a whole world of alternatives that would make it much better off road.

Sooo. How do you like my old bike? BTW I gave Chase all the take off parts inc.. the stock seat cover and foam. I still have the GPR titanium exh . I had on it .

Close encounters of the 3rd kind 👀

still very helpful years later

Nice work

Awesome video- I have a GT250 (1974) that I got at the HUGE auction/show in Carlisle Pa, for 500.00. I am making a little cafe out of her for my wife. Going through everything now and getting ready to install points and condensers. I was going to go with electronic ignition, but for now- just the old school way. Thanks for the great video! By the way, I subscribed and "liked"

Hey can you fix my kx?

How do I contact you guys for help building my own tug similar to this one?

A proper adventure

Looks like an awesome trip man, have always wanted to do a top gear type road trip, how'd your luggage rack and skid plate hold up?

Hi, I’m looking to build something similar to this. Would you mind telling me how you secured the wheel pan? Did you use a linear actuator, electromagnets or is it manual only?

Your bell housing is a mid 1929. Very helpful video!

Good luck brother, sounds like a fun experience

hello, i'm thinking of buying this bike for long travel with my wife. is it comfortable with a pillion ? thank's

Gizmowerks! bravo!insane . =)

Really enjoying these vids, have been doing similar stuff to my also newish TR650. Check out the SW-Motech engine guards they go on in five minutes and will protect the radiator for certain. Mounts to the upper side engine mount near the head and the top bolt of that lower central engine mount. The Happy Trails skid plate is a tank if you decide to buy one instead.

Yo hope you and the big red are still around... mine is over jetted .. if fuel is on it get way to much gas and only shittly runs full throttle .. when i turn fuel off with it running after a few seconds it runs and revs like a champ for a few seconds Then dies.. my cheap carb is different from yours it came with my BR.. so not sure if it matters on that fact but what were the final jet sizes .. i didnt hear ya say.. thanks good video .. maybe update description with jets sizes

Do you have the link to the clone carb you have? I’ve bought 2 so far and they are way too big and not the correct fit for my big red.

Amazing. You saved me both time and money!

Update: I let this engine go to a guy building Kolb Fireflys

Did you have to change anything on the wiring or on the machine, besides the plug, to swap between 110 and 220 v?

I am looking for a ignition for my Suzuki GT185 / what make is this.

I like the video my basket keep going up and down and water doest get hot any help thank you

Thanks. This video is exactly what I needed to see.

JUST SUBSCRIBED!!!👍👍👍👍👍👍

Wow what a great idea I’m getting a brand new hand brake cable tomorrow my snap. I just bought a 1998 Honda fourtrax 450ES green just like the one you have . I have to replace the temperature sensor sometimes red light comes on but goes away I will start with that then I will see if is something else. Fan works I heard it sometimes. Thank you so much for sharing

Good to find your channel, I'm the other guy with a TR 😁

I did this repair (using a thermal fuse to replace the unavailable cutout) then found it would boil and never shut off. I had to take the base apart (remove the 2 screws you can see, then pull off the 2 rubber feet furthest to the back and remove the 2 screws under them (there are no screws under the front feet) then take the base apart, remove the circuit board and replace the relay on the circuit board. (It's soldered in) Thanks for the great video!

Fuckin huge🤣

Always good to see your content my friend

Hello great channel very nice ride ;)